GE Bently 33300 XL 11mm Proximity Transducer System

GE Bently 3300 XL 11mm Proximity Transducer System

GE Bently 3300 XL 8mm Proximity Transducer System

The 3300 XL 11 mm Proximity Transducer System consists of:

3300 XL 11 mm probe 3300 XL 11 mm extension cable 3300 XL 11 mm Proximitor® Sensor

The 3300 XL 11 mm Proximity Transducer System has a 3.94 V/mm (100 mV/mil) output for non-contacting vibration and displacement measurements on fluid film bearing machines. The large 11 mm tip enables this transducer system to have a longer linear range compared to our standard 3300 XL 8 mm Transducer System.

 

It is primarily used in the following applications where the longer linear range is necessary:

  • Axial (thrust) position measurements
  • Ramp differential expansion measurements on steam turbines
  • Rod position or rod drop measurements on reciprocating compressors
  • Tachometer and zero speed measurements
  • Phase reference (Keyphasor®) signals

The 3300 XL 11 mm Proximitor Sensor is designed to replace the 7200-series 11mm and 14 mm Transducer Systems. When upgrading from the 7200-series system to the 3300 XL 11 mm system, every component must be replaced with 3300 XL 11 mm components. In addition, the monitoring system must be updated. If using a 3500 Monitoring System, an updated version of the configuration software that lists the 3300 XL 11 mm Transducer System as a compatible option is required. Existing 3300 Monitoring Systems may need a modification. Contact your local sales and service representative for assistance.

GE Bently 33300 XL 11mm Proximity Transducer System - Diagram

Specification

Unless otherwise noted, the following specifications are for a 3300 XL 11 mm Proximitor Sensor,extension cable and probe between 0°C and +45°C (+32°F to +113°F), with a -24 Vdc power supply, a 10 kW load, our supplied AISI 4140 steel target that is 31mm (1.2 in) diameter or larger, and a probe gap of 2.5 mm (100 mils). The system accuracy and interchangeability specifications do not apply when using a transducer system calibrated to any target other than our AISI 4140 steel target.

Proximitor
Sensor Input :Accepts one noncontacting 3300 XL 11 mm Proximity Probe and Extension Cable.

Power
Requires -17.5 Vdc to -26 Vdc without barriers at 12 mA maximum consumption, -23 Vdc to -26 Vdc with barriers.

Operation at a more positive voltage than -23.5 Vdc can result in reduced linear range.

Supply Sensitivity: Less than 2 mV change in output voltage per volt change in input voltage.

Output resistance:  50 W

Probe Tip Material: Polyphenylene sulfide (PPS).

Probe Case Material: AISI 304 stainless steel (SST).

Probe Cable Specifications: 75 W triaxial, fluoroethylene propylene (FEP) insulated probe cable in the following total probe lengths: 1, 5 or 9 metres.

Extension Cable Material: 75 W triaxial, fluoroethylene propylene (FEP) insulated.

Proximitor® Sensor Material: A380 aluminum

System Length:5 or 9 metres including extension cable

Extension Cable Armor (optional): Flexible AISI 302 SST with FEP outer jacket.

Tensile Strength (maximum rated): 330 N (75 pounds) probe case to probe lead. 270 N (60 pounds) at probe lead to extension cable connectors.

Connector material: Gold-plated brass

Probe case torque:                                Maximum Rated          Recommended

½-20 and 5⁄8 -18 probe cases            45.2 N•m(400 in•lb)    15.0 N•m(133 in•lb)

M14x1.5 and M16x1.5 probe cases     63.3 N•m(560 in•lb)    21.1 N•m(187 in•lb)

Reverse mount probes                         22.6 N•m(200 in•lb)       7.5 N•m(66 in•lb)

Connector-to-connector torque

Recommended torque: Finger tight

Maximum torque:0.565 N•m (5 in•lb)

Minimum Bend Radius (with or without sst armor): 25.4 mm (1.0 in)

System Weight (typical):

Probe:

  • 70 g (2.5 oz) (minimum length case, 1m lead, no armor)
  • 170 g (6.0 oz) (minimum length case, 1m lead, with armor)
  • For longer case lengths add 1.1g/mm (1.0 oz/in).
  • For 5 m probe length add 180 g (6oz) for non-armored probe or 560 g (20 oz) for armored probe.
  • For 9 m probe length add 360 g (12oz) for non-armored probe or 1120g (40 oz) for armored probe.

Extension Cable: 45 g/m (0.5 oz/ft) Armored

Extension cable: 140 g/m (1.5 oz/ft)

Proximitor Sensor: 255 g (9 oz)

Probe Temperature Range Operating and Storage Temperature: -51°C to +177°C (-60°F to +351°F)

Note: Exposing the probe to temperatures below -34°C (-30°F) may cause premature failure of the pressure seal.

Extension Cable Temperature Range Operating and Storage Temperature: -51°C to +177°C (-60°F to +351°F)

Proximitor Sensor Temperature Range Operating Temperature:-35°C to +85°C (-31°F to +185°F)

Storage Temperature: -51°C to +100°C (-60°F to +212°F)

Relative Humidity: 100% condensing, nonsubmersible when connectors are protected. Tested to IEC 68-2-3 damp heat.

Probe Pressure: 3300 XL probes are designed to seal differential pressure between the probe tip and case. The probe sealing material consists of a Viton® O-ring. Probes are not pressure tested prior to shipment.

Components

3300 XL 11 mm Proximity Probes:
330701 3300 XL 11 mm Probe, 1/2-20 UNF thread, without armor
330702 3300 XL 11 mm Probe, 1/2-20 UNF thread, with armor
330707 3300 XL 11 mm Probe, 5/8-18 UNF thread, without armor
330708 3300 XL 11 mm Probe, 5/8-18 UNF thread, with armor
Specifications and Ordering Information
Part Number 146256-01
Rev. C (05/07)
Page 7 of 22
Part Number-AXX-BXX-CXX-DXX-EXX
Option Descriptions
A: Unthreaded Length Option
Note: Unthreaded length must be at least
  • 1.0 inch less than the case length.
  • Order in increments of 0.1 in
  • Length configurations:
  • Maximum unthreaded length: 8.9 in
  • Minimum unthreaded length: 0.0 in
  • Example: 0 4 = 0.4 in
B: Overall Case Length Option
  • Order in increments of 0.1 in
  • Threaded length configurations:
  • Maximum case length: 9.9 in
  • Minimum case length: 1.0 in
  • Example: 2 4 = 2.4 in
C: Total Length Option
  • 1 0 1.0 metre (3.3 feet)
  • 5 0 5.0 metres (16.4 feet)
  • 9 0 9.0 metres (29.5 feet)
Note: Five metre probes are designed for use with the five metre Proximitor Sensor only.
D: Connector and Cable-Type Option
  • 0 1 Miniature coaxial ClickLoc connector with connector protector, standard cable
  • 0 2 Miniature coaxial ClickLoc connector, standard cable
  • 1 1 Miniature coaxial ClickLoc connector with connector protector, FluidLoc cable
  • 1 2 Miniature coaxial ClickLoc connector, FluidLoc cable
E: Agency Approval Option
  • 0 0 Not required
  • 0 5 Multiple Approvals

3300 XL 11 mm Proximity Probes, Metric:
330703 3300 XL 11 mm Probe, M14 x 1.5 thread, without armor
330704 3300 XL 11 mm Probe, M14 x 1.5 thread, with armor
330709 3300 XL 11 mm Probe, M16 x 1.5 thread, without armor
330710 3300 XL 11 mm Probe, M16 x 1.5 thread, with armor
Part Number-AXXX-BXXX-CXX-DXX-EXX
Option Descriptions
A: Unthreaded Length Option
Note: Unthreaded length must be at least
  • 26 mm less than the case length.
  • Order in increments of 2 mm.
  • Length configuration: Maximum unthreaded length: 224mm Minimum unthreaded length: 0 mm
  • Example: 0 6 0 = 60 mm
B: Overall Case Length Option
  • Order in increments of 2 mm.
  • Metric thread configurations:
  • Maximum length: 250 mm
  • Minimum length: 26 mm
  • Example: 0 6 0 = 60 mm
C: Total Length Option
  • 1 0 1.0 metre (3.3 feet)
  • 5 0 5.0 metres (16.4 feet)
  • 9 0 9.0 metres (29.5 feet)
Note: Five metre probes are designed for use with the five metre Proximitor Sensor only.
D: Connector and Cable-Type Option
  • 0 1 Miniature coaxial ClickLoc connector with connector protector, standard cable
  • 0 2 Miniature coaxial ClickLoc connector, standard cable
  • 1 1 Miniature coaxial ClickLoc connector with connector protector, FluidLoc cable
  • 1 2 Miniature coaxial ClickLoc connector, FluidLoc cable
E: Agency Approval Option
  • 0 0 Not required
  • 0 5 Multiple Approvals

3300 XL 11 mm Reverse Mount Probe
330705-02-18- CXX-DXX-EXX, 3/8-24 UNF threads
330706-005-046- CXX-DXX-EXX, M10 x 1 threads
Option Descriptions
C: Total Length Option
  • 1 0 1.0 metre (3.3 feet)
  • 5 0 5.0 metres (16.4 feet)
  • 9 0 9.0 metres (29.5 feet)
Note: Five metre probes are designed for use with the five metre Proximitor Sensor only.
D: Connector Option
  • 0 2 Miniature ClickLoc coaxial connector
E: Agency Approval Option
  • 0 0 Not required
  • 0 5 Multiple Approvals
Note: For a shorter delivery time, order commonly stocked probes. Currently, stocked probes consist of the following part numbers: 330701-00-10-10-02-00,
330701-00-20-10-02-00, 330703-000-050-10-02-00, 330705-02-18-10-02-00, 330706-005-046-10-02-00.

3300 XL 11 mm Proximitor Sensor
330780-AXX-BXX
Option Descriptions
A: Total Length and Mounting Option 
  • 5 0 5.0 metre (16.4 feet) system length, panel mount
  • 5 1 5.0 metre (16.4 feet) system length, DIN mount
  • 5 2 5.0 metre (16.4 feet) system length, no mounting hardware
  • 9 0 9.0 metres (29.5 feet) system length, panel mount
  • 9 1 9.0 metres (29.5 feet) system length, DIN mount
  • 9 2 9.0 metres (29.5 feet) system length, no mounting hardware
B: Agency Approval Option
  • 0 0 Not required
  • 0 5 Multiple approvals

3300 XL 11 mm Extension Cable
330730-AXXX-BXX-CXX
Note: Make sure that the extension cable length and the probe length, when added together, equal the Proximitor Sensor total length.
Option Descriptions
A: Cable Length Option
  • 0 4 0 4.0 metres (13.1 feet)
  • 0 8 0 8.0 metres (26.2 feet)
B: Connector and Cable Option
  • 0 0 Standard cable
  • 0 1 Armored cable
  • 0 2 Standard cable with connector protectors
  • 0 3 Armored cable with connector protectors
  • 1 0 FluidLoc cable
  • 1 1 Armored FluidLoc cable
  • 1 2 FluidLoc cable with connector protectors
  • 1 3 Armored FluidLoc cable with connector protectors
C: Agency Approval Option
  • 0 0 Not required
  • 0 5 Multiple Approvals

 

 

 

 

 

 

General Electric Energy Bently

 

GE

source : http://www.ge-energy.com/bently

Line